Sliding Patio Door Roller Assembly for Truth Part #31761A, Jeld Wen, Milgard,...

Description: Sliding Patio Door Roller Assembly for Truth Part #31761A, Jeld Wen, Milgard, Marvin, Peachtree, Caradco, 1-1/4" Steel Ball Bearing, Side Adjustable, 2 PackReplace Old or Damaged Rollers: Commonly used to replace rollers on wood, extruded aluminum or vinyl sliding patio doors manufactured by Weathershield, Andersen, Malta, Pozzi, Hurd, Peachtree, Jeld Wen, Milgard, Marvin, Caradco and others.Heavy Duty Construction: Premium dual steel ball bearing wheels still work smoothly and noiselessly after a 100,000 cycle test with 2 rollers bearing 265 lbs. While others may use the bearings made from Carbon Steel W/O heat treating, we insists all bearings made from Heat Treated Bearing Steel.Easy to install & Adjust: Easy to install in less than 30 minutes with a few simple tools. This roller assembly features side leveling adjustment and has a minimum collapsed height at 1-1/2 inch.Standard Dimension: Heavy duty 1-1/4 inch steel ball bearing wheel with 11/16 inch thick housing and 5-3/4 inch hole centers. For further dimensional information, please see the line drawing.Package Includes: Includes 2 pack of sliding patio door rollers, we recommend replacing both rollers at the same time. Screws NOT included, because different type of doors may have different type of screws, single wrong one could just ruin your glass doors!Product DescriptionMaterial: ‎Heat Treated SteelColor/Finish: ‎Yellow Zinc PlatedScrew holes spaced at 5-3/4 inches (Screws NOT included).Concaved Roller Dimensions: 1-1/4-inch O.D. x 5/16-inch WideHousing Dimensions(LxWxH): 4-5/8-inch x 11/16-inch x 1-3/16-inch*Before you order: You have to measure the size of your old rollers, length, width, height and type of mount of the assembly, to make sure it matches as closely as possible. Depending on door and roller, you may have to do some adjustment of the door to make it fit.Following instructions are meant to guide homeowners in replacing the rollers in their sliding doorsReplacing steel tandem rollers for Andersen Primed gliding doors: Part #1273704used on gliding doors manufactured from 1967-1983You will need two screws and a drill to secure rollers by screwing in place on bottom of door.You may have to shave bore top of door down a bit to make it fit.An alternative for Truth 31761A & Truth 30410 1-1/4" side adjust tandem rollers.Features in adjustments from both sides:When turned counter-clockwise, the side with crossed slots raises the door;When turned clockwise, the side with the single slot raises the door;How To Adjust Sliding Patio Door RollersMany wooden patio doors have tandem roller assemblies that allow it to slide open and closed smoothly.These rollers adjust vertically, so the wheels can be raised or lowered to raise or lower your door panel without removing from its frame.The rollers can easily adjust from the outside when a small plastic hole cap at the bottom of the door panel removed. After exposing the adjustment screw on the roller, you need to use a flathead or phillips screwdriver to do the job.Some roller assemblies turn clockwise to raise the panel and counter-clockwise to lower it. Carefully try turning your screwdriver one way or the other to figure out which direction you need to turn.How to Install Tandem Rollers*Before you begin: Note that extreme caution must be exercised when handling and lifting sliding door panels; doors are heavy and can cause injury if not handled properly. Always enlist the help of a partner when lifting panels in and out of door frame.Remove the active patio door panel.Remove the adjustment screw hole cap.Take your screwdriver to pry the old rollers out.Push our new roller assemblies into position.Secure it tight with the screws (NOT included).Repeat step 2-5 on other side to replace another roller.Clean your roller track.Put door panel back in frame.Adjust side screw to fit your door perfectly.Put the plastic hole cover back in.

Price: 23.99 USD

Location: polonnaruwa

End Time: 2025-02-04T04:00:03.000Z

Shipping Cost: 0 USD