FORD FS10 FX15 HS18 HS20 AC Compressor Reseal Kit Oring Shaft Seal BLACK RUBBER

Description: PLEASE NOTE: SUNAIR HAS DISCONTINURED THEIR FS10 PLASTIC "SHAFT SEAL INSTALL/PROTECTOR TOOL" . The Shaft Seal Install/Protector Tool is a "REQUIRED" item. You MUST USE the tool to install the SEAL with a plastic "TEFLON LIP" seal. IF not YOU WILL DAMAGE the Seal EVERYTIME with each try in any attempt to install a Seal new or even a used Seal WITHOUT the REQUIRED Tool. The Shaft Seal INSTALL/PROTECTOR TOOL is NOT INCLUDED!!!! _____________________________________________________________________________ Made by Sunair NEW STOCK! NOT old stock! {:O)~ These are NOT NOS (New Old Stock) PLEASE NOTE:THIS kit BLACK NEOPRENE LARGE CASE HOUSING ORING and 2 GREEN HNBR MANIFOLD HOSE ORINGS as pictured! Master Reseal Kit for FS10 FX15 HS18 HS20 AC Compressors Fits:- Ford FS-10 and Ford FX-15 AC Compressors - HCC HS-18 and HS-20 AC Compressors HCC HS-18 and HS-20 AC Compressors are commonly found on Hyundai, Kia, and "some" Chrysler Dodge Mopar products. Includes: - SK-731N Shaft Seal Kit - -155G Case Housing O-Ring - in BLACK NEOPRENE RUBBER!!!!! - TWO -211G Manifold Gaskets GREEN HNBR O-Rings____________________________________________________________________________________________________ PLEASE NOTE: A REQUIRED INSTALL/PROTECTOR TOOL IS NOT INCLUDED! Please Note: A Plastic Shaft Seal Protector / Install Tool is considered a one time use, "tight fitting" tool by design tool. (If you don't like the Plastic Seal Protector / Install Tool or have problems using it YOU should BUY AND USE a Professional METAL Protector / Install Tool made by Mastercool part number 91328 for professional results that Professionals use. THAT WAS A TIP!!!!!!! ____________________________________________________________________________________________ This listing is for a Compressor Reseal Kit to reseal Ford FS-10 AC Compressors, Ford FX15 Compressors, HCC HS-18 AC Compressors, and HS-20 AC Compressors. IF you remove the compressor's front nose cone / front head the shaft seal can be removed without a special shaft seal remover tool. The easiest way to remove the shaft seal is to open the compressor case housing & drive the shaft seal out from behind (inside the compressor). Then replace the "included" center case housing O-Ring and bolt the compressor back together. The 2 included Manifold Gasket O-Rings may be different on "some" compressor applications. This kit only includes what is shown in the posted pictures. THIS KIT IS COMPATIBLE WITH BOTH R12 AND R134A REFRIGERANTS. Video shows how to reseal Ford FS10, Halla HS18, and HS20 used on Ford, Hyundai, Kia, and Dodge Ram vehicles. can be found on You Tube by searching the following key words: Replacing FS10 Compressor Shaft Seals https://www.youtube.com/watch?v=x8J9uuYaJDI&t=184s A/C Compressor Shaft Seal Installation Tips Video: https://www.youtube.com/watch?v=YuItapsCDcw______________________________________________________ TORQUE SPEC: Thru Bolt Torque Spec for FS10, FX15, HS18, HS20 Compressors: 18 Foot lbs Install the NEW clutch plate bolt, and tighten to 98-123 INCH lbs. (11-14 N.m). Using a feeler gauge, measure air gap between clutch plate and pulley assembly mating surfaces in 3 places. Air gap should be 0.014-0.030" (0.36-0.75 mm). If air gap is not as specified, add or remove shims as necessary._______________________________________________________ Features & Benefits: These O-Rings Gaskets are manufactured from the highest quality Premium GREEN HNBR Rubber and are compatible with BOTH R12 and R134a refrigerant. These are Premium GREEN HNBR Rubber O-Ring Gasket Kits. High quality GREEN HNBR Rubber O-Rings as needed for R-134a High Temperature usage. These are IMPROVED DESIGN Rubber and considered an UPGRADE to R-12 standard Black "NITRILE" Rubber AND R-134a Black " NEOPRENE" Rubber. GREEN HNBR Rubber AND BLACK NEOPRENE O-rings are compatible with R12 and R134a. Don't buy lower quality BLACK "Nitrile" Rubber O-Ring Gasket Kits from other sellers. A shaft seal Protector is REQUIRED for Teflon compressor shaft seal installation. The tool protects, EXPANDS, and STRETCHES the Teflon (Plastic) Lip seal to install the seal. Without the tool you WILL damage the new shaft seal by improperly installing it. The Shaft seal protector is REQUIRED if you are to install a seal without damaging the new seal. Without the tool how will you expand the Teflon Lip seal to install it? Teflon seals are not like rubber seals. Teflon seal are actually manufactured with a smaller inside diameter than the actual compressor shaft. That is why you MUST use this tool to properly install the new seal. PLEASE NOTE:ALL PICTURES ARE OF THE EXACT SEAL. IT IS IMPORTANT TO LOOK AT THE SEAL YOU ARE REMOVING AND CALL IF YOU HAVE ANY QUESTIONS AT ALL! VISUAL COMPARISON IS REQUIRED. MANY SEALS FIT MORE THAN ONE COMPRESSOR AND MANY COMPRESSORS HAVE MORE THAN 1 SEAL THAT IS USED. I AM NOT RESPONSIBLE FOR SEALS ORDERED INCORRECTLY. Visual comparison required! Buyers in Continental USA (including Alaska, Hawaii, & Puerto Rico) get FREE shipping via USPS First Class Mail shipping. No sales outside Continental USA. (except Alaska, Hawaii, & Puerto Rico) No sales to APO/FPO addresses. No exceptions, No excuses, PERIOD!

Price: 24.99 USD

Location: Florida

End Time: 2024-09-08T18:31:26.000Z

Shipping Cost: 0 USD